Page 1 of 1
Decoding Enable/Disable doesn't work 1.36.9
Posted: Fri Oct 22, 2021 3:18 pm
by geraldbrandt
Hi,
I just upgraded to 1.36.9 and my system load shot through the roof. I have Decoding Enable turned off for a lot my monitors, and it worked great in 1.36.8. In 1.36.9 all my monitors are decoding despite the setting.
Is it just me, or has anyone else seen this?
Gerald
Re: Decoding Enable/Disable doesn't work 1.36.9
Posted: Fri Oct 22, 2021 7:05 pm
by guynew
Hi Gerald,
I have exactly the same problem (see
viewtopic.php?f=43&t=31219). All was fine until I updated the software from 1.36.8 to 1.36.9. I am using Reolink 520 H264 cameras on an Ubuntu 20.04.3 server.
Kind regards ... Guy
Re: Decoding Enable/Disable doesn't work 1.36.9
Posted: Fri Oct 22, 2021 9:47 pm
by geraldbrandt
I have it on multiple cameras: 1 reolink, 2 dahua, and 2 ezviz, all FFMpeg RTSP or RTMP.
Re: Decoding Enable/Disable doesn't work 1.36.9
Posted: Sat Oct 23, 2021 4:36 pm
by guynew
Looked at the system this morning (after two days of continuous running with no changes to Ubuntu server or ZM config software) and the high res stream had stopped hogging CPU and the live stream was off, just as things should be! So I restarted ZM service to see if the problem was cured, but unfortunately the high res stream went back to high CPS usage and showing live view again???
Does anyone know if it is possible to downgrade to 1.36.8 using Ubuntu? I have tried 'sudo apt-get install zoneminder=1.36.8' but it returns that this version is not found.
Many thanks.
Re: Decoding Enable/Disable doesn't work 1.36.9
Posted: Sat Oct 23, 2021 5:10 pm
by Magic919
You could go to the PPA, grab the old version .deb file and install using dpkg.
Re: Decoding Enable/Disable doesn't work 1.36.9
Posted: Sat Oct 23, 2021 7:16 pm
by Fr0gger
That was my first thought as well, but it seems that 1.36.8 and .7 are no longer present on either of the below URLs. Anyone know if there's an archive for previously-built 1.36.x deb packages?
(1.36.7 had some high mem issues after running for ~ 1 week, but CPU usage wasn't problematic.)
http://ppa.launchpad.net/iconnor/zonemi ... oneminder/
https://zmrepo.zoneminder.com/debian/master/focal/
Thanks,
Dan
Re: Decoding Enable/Disable doesn't work 1.36.9
Posted: Sun Oct 24, 2021 11:55 am
by Magic919
Re: Decoding Enable/Disable doesn't work 1.36.9
Posted: Mon Oct 25, 2021 1:05 am
by Fr0gger
Thanks! Those packages work and resolve the high CPU issue.
Re: Decoding Enable/Disable doesn't work 1.36.9
Posted: Mon Oct 25, 2021 2:17 pm
by geraldbrandt
I rolled back as well. Hopefully we'll see a .10 to solve this issue.
Re: Decoding Enable/Disable doesn't work 1.36.9
Posted: Mon Oct 25, 2021 3:53 pm
by Magic919
Provided someone makes the devs aware of course.
Re: Decoding Enable/Disable doesn't work 1.36.9
Posted: Tue Oct 26, 2021 9:37 am
by Magic919
1.36.10 is there now.
Re: Decoding Enable/Disable doesn't work 1.36.9
Posted: Tue Oct 26, 2021 10:16 am
by guynew
Hi Everyone,
Just wanted to say a big thank you to the Zoneminder community and developers. Installed 1.36.10 this morning and the Decoding Enable/Disable flag is working again.
Thank you ... Guy
Re: Decoding Enable/Disable doesn't work 1.36.9
Posted: Wed Oct 27, 2021 1:57 pm
by geraldbrandt
Wonderful! Works for me too.