Hi,
can anybody help me solve this problem?
I run zoneminder 1..22.3 with Kodicom 8800 capture board. I finally see streaming video on /dev/video0, but when I connect another monitor for ex: /dev/video1 I get blue screen with fps srolling at the bottom.
zmu -d /dev/video0 -q -v
Video Capabilities
Name: BT878 video ( *** UNKNOWN/GENER
Type: 171
Can capture
Can tune
Overlay onto frame buffer
Can clip
Scalable
Video Channels: 4 -->strange it supposed to be 8 ch.
Audio Channels: 1
Maximum Width: 768
Maximum Height: 480
Minimum Width: 48
Minimum Height: 32
Window Attributes
X Offset: 0
Y Offset: 0
Width: 352
Height: 288
Picture Attributes
Palette: 4 - 24bit RGB
Colour Depth: 24
Brightness: 32768
Hue: 32768
Colour :32768
Contrast: 32768
Whiteness: 0
Channel 0 Attributes
Name: Television
Channel: 0
Flags: 3
Channel has a tuner
Channel has audio
Type: 1 - TV
Format: 1 - NTSC
Channel 1 Attributes
Name: Composite1
Channel: 1
Flags: 2
Channel has audio
Type: 2 - Camera
Format: 1 - NTSC
Channel 2 Attributes
Name: S-Video
Channel: 2
Flags: 2
Channel has audio
Type: 2 - Camera
Format: 1 - NTSC
Channel 3 Attributes
Name: Composite3
Channel: 3
Flags: 2
Channel has audio
Type: 2 - Camera
Format: 1 - NTSC
run on:
AMD 4400+
ASUS M2N-MX SE PLUS
1 GB memory
GeForce 7300GS 256Mb
Fedora Core 7
Thank you for your help!
Got video on /dev/video0, blue screen on other inputs.
Dmesg
Here<s> Link [LNKB] -> GSI 11 (level, low) -> IRQ 11
bttv0: Bt878 (rev 17) at 0000:02:08.0, irq: 11, latency: 64, mmio: 0xbffff000
bttv0: using: *** UNKNOWN/GENERIC *** [card=0,autodetected]
bttv0: gpio: en=00000000, out=00000000 in=00ffffff [init]
bt878: Unknown symbol bttv_read_gpio
bt878: Unknown symbol bttv_write_gpio
bt878: Unknown symbol bttv_gpio_enable
ACPI: PCI Interrupt Link [LAZA] enabled at IRQ 11
ACPI: PCI Interrupt 0000:00:05.0 -> Link [LAZA] -> GSI 11 (level, low) -> IRQ 11
PCI: Setting latency timer of device 0000:00:05.0 to 64
hda_codec: Unknown model for ALC662, trying auto-probe from BIOS...
hda_codec: num_steps = 0 for NID=0xc
tveeprom 2-0050: Huh, no eeprom present (err=-121)?
bttv0: tuner type unset
bttv0: i2c: checking for MSP34xx @ 0x80... not found
bttv0: i2c: checking for TDA9875 @ 0xb0... not found
bttv0: i2c: checking for TDA7432 @ 0x8a... not found
bttv0: registered device video0
bttv0: registered device vbi0
bttv: Bt8xx card found (1).
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 10
ACPI: PCI Interrupt 0000:02:09.0[A] -> Link [LNKC] -> GSI 10 (level, low) -> IRQ 10
bttv1: Bt878 (rev 17) at 0000:02:09.0, irq: 10, latency: 64, mmio: 0xbfffd000
bttv1: using: *** UNKNOWN/GENERIC *** [card=0,autodetected]
bttv1: gpio: en=00000000, out=00000000 in=00ffffff [init]
hda_codec: num_steps = 0 for NID=0xc
hda_codec: num_steps = 0 for NID=0xc
hda_codec: num_steps = 0 for NID=0xc
hda_codec: num_steps = 0 for NID=0xc
tveeprom 3-0050: Huh, no eeprom present (err=-121)?
bttv1: tuner type unset
bttv1: i2c: checking for MSP34xx @ 0x80... not found
bttv1: i2c: checking for TDA9875 @ 0xb0... not found
bttv1: i2c: checking for TDA7432 @ 0x8a... not found
bttv1: registered device video1
bttv1: registered device vbi1
bttv: Bt8xx card found (2).
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11
ACPI: PCI Interrupt 0000:02:0a.0[A] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11
bttv2: Bt878 (rev 17) at 0000:02:0a.0, irq: 11, latency: 64, mmio: 0xbfffb000
bttv2: using: *** UNKNOWN/GENERIC *** [card=0,autodetected]
bttv2: gpio: en=00000000, out=00000000 in=00ffffff [init]
tveeprom 4-0050: Huh, no eeprom present (err=-121)?
bttv2: tuner type unset
bttv2: i2c: checking for MSP34xx @ 0x80... not found
bttv2: i2c: checking for TDA9875 @ 0xb0... not found
bttv2: i2c: checking for TDA7432 @ 0x8a... not found
bttv2: registered device video2
bttv2: registered device vbi2
bttv: Bt8xx card found (3).
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
ACPI: PCI Interrupt 0000:02:0b.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
bttv3: Bt878 (rev 17) at 0000:02:0b.0, irq: 11, latency: 64, mmio: 0xbfff9000
bttv3: using: *** UNKNOWN/GENERIC *** [card=0,autodetected]
bttv3: gpio: en=00000000, out=00000000 in=00ffffff [init]
tveeprom 5-0050: Huh, no eeprom present (err=-121)?
bttv3: tuner type unset
bttv3: i2c: checking for MSP34xx @ 0x80... not found
bttv3: i2c: checking for TDA9875 @ 0xb0... not found
bttv3: i2c: checking for TDA7432 @ 0x8a... not found
bttv3: registered device video3
bttv3: registered device vbi3
bttv: Bt8xx card found (4).
ACPI: PCI Interrupt 0000:02:0c.0[A] -> Link [LNKB] -> GSI 11 (level, low) -> IRQ 11
bttv4: Bt878 (rev 17) at 0000:02:0c.0, irq: 11, latency: 64, mmio: 0xbfff7000
bttv4: using: *** UNKNOWN/GENERIC *** [card=0,autodetected]
bttv4: gpio: en=00000000, out=00000000 in=00ffffff [init]
tveeprom 6-0050: Huh, no eeprom present (err=-121)?
bttv4: tuner type unset
bttv4: i2c: checking for MSP34xx @ 0x80... not found
bttv4: i2c: checking for TDA9875 @ 0xb0... not found
bttv4: i2c: checking for TDA7432 @ 0x8a... not found
bttv4: registered device video4
bttv4: registered device vbi4
bttv: Bt8xx card found (5).
ACPI: PCI Interrupt 0000:02:0d.0[A] -> Link [LNKC] -> GSI 10 (level, low) -> IRQ 10
bttv5: Bt878 (rev 17) at 0000:02:0d.0, irq: 10, latency: 64, mmio: 0xbfff5000
bttv5: using: *** UNKNOWN/GENERIC *** [card=0,autodetected]
bttv5: gpio: en=00000000, out=00000000 in=00ffffff [init]
tveeprom 7-0050: Huh, no eeprom present (err=-121)?
bttv5: tuner type unset
bttv5: i2c: checking for MSP34xx @ 0x80... not found
bttv5: i2c: checking for TDA9875 @ 0xb0... not found
bttv5: i2c: checking for TDA7432 @ 0x8a... not found
bttv5: registered device video5
bttv5: registered device vbi5
bttv: Bt8xx card found (6).
ACPI: PCI Interrupt 0000:02:0e.0[A] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11
bttv6: Bt878 (rev 17) at 0000:02:0e.0, irq: 11, latency: 64, mmio: 0xbfff3000
bttv6: using: *** UNKNOWN/GENERIC *** [card=0,autodetected]
bttv6: gpio: en=00000000, out=00000000 in=00ffffff [init]
tveeprom 8-0050: Huh, no eeprom present (err=-121)?
bttv6: tuner type unset
bttv6: i2c: checking for MSP34xx @ 0x80... not found
bttv6: i2c: checking for TDA9875 @ 0xb0... not found
bttv6: i2c: checking for TDA7432 @ 0x8a... not found
bttv6: registered device video6
bttv6: registered device vbi6
bttv: Bt8xx card found (7).
ACPI: PCI Interrupt 0000:02:0f.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
bttv7: Bt878 (rev 17) at 0000:02:0f.0, irq: 11, latency: 64, mmio: 0xbfff1000
bttv7: using: *** UNKNOWN/GENERIC *** [card=0,autodetected]
bttv7: gpio: en=00000000, out=00000000 in=00ffffff [init]
tveeprom 9-0050: Huh, no eeprom present (err=-121)?
bttv7: tuner type unset
bttv7: i2c: checking for MSP34xx @ 0x80... not found
bttv7: i2c: checking for TDA9875 @ 0xb0... not found
bttv7: i2c: checking for TDA7432 @ 0x8a... not found
bttv7: registered device video7
bttv7: registered device vbi7
bt878: AUDIO driver version 0.0.0 loaded
bt878: Bt878 AUDIO function found (0).
ACPI: PCI Interrupt 0000:02:08.1[A] -> Link [LNKB] -> GSI 11 (level, low) -> IRQ 11
bt878_probe: card id=[0x0], Unknown card.
Exiting..
ACPI: PCI interrupt for device 0000:02:08.1 disabled
bt878: probe of 0000:02:08.1 failed with error -22
bt878: Bt878 AUDIO function found (0).
ACPI: PCI Interrupt 0000:02:09.1[A] -> Link [LNKC] -> GSI 10 (level, low) -> IRQ 10
bt878_probe: card id=[0x0], Unknown card.
Exiting..
ACPI: PCI interrupt for device 0000:02:09.1 disabled
bt878: probe of 0000:02:09.1 failed with error -22
bt878: Bt878 AUDIO function found (0).
ACPI: PCI Interrupt 0000:02:0a.1[A] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11
bt878_probe: card id=[0x0], Unknown card.
Exiting..
ACPI: PCI interrupt for device 0000:02:0a.1 disabled
bt878: probe of 0000:02:0a.1 failed with error -22
bt878: Bt878 AUDIO function found (0).
ACPI: PCI Interrupt 0000:02:0b.1[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
bt878_probe: card id=[0x0], Unknown card.
Exiting..
ACPI: PCI interrupt for device 0000:02:0b.1 disabled
bt878: probe of 0000:02:0b.1 failed with error -22
bt878: Bt878 AUDIO function found (0).
ACPI: PCI Interrupt 0000:02:0c.1[A] -> Link [LNKB] -> GSI 11 (level, low) -> IRQ 11
bt878_probe: card id=[0x0], Unknown card.
Exiting..
ACPI: PCI interrupt for device 0000:02:0c.1 disabled
bt878: probe of 0000:02:0c.1 failed with error -22
bt878: Bt878 AUDIO function found (0).
ACPI: PCI Interrupt 0000:02:0d.1[A] -> Link [LNKC] -> GSI 10 (level, low) -> IRQ 10
bt878_probe: card id=[0x0], Unknown card.
Exiting..
ACPI: PCI interrupt for device 0000:02:0d.1 disabled
bt878: probe of 0000:02:0d.1 failed with error -22
bt878: Bt878 AUDIO function found (0).
ACPI: PCI Interrupt 0000:02:0e.1[A] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11
bt878_probe: card id=[0x0], Unknown card.
Exiting..
ACPI: PCI interrupt for device 0000:02:0e.1 disabled
bt878: probe of 0000:02:0e.1 failed with error -22
bt878: Bt878 AUDIO function found (0).
ACPI: PCI Interrupt 0000:02:0f.1[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
bt878_probe: card id=[0x0], Unknown card.
Exiting..
ACPI: PCI interrupt for device 0000:02:0f.1 disabled
bt878: probe of 0000:02:0f.1 failed with error -22
bttv0: Bt878 (rev 17) at 0000:02:08.0, irq: 11, latency: 64, mmio: 0xbffff000
bttv0: using: *** UNKNOWN/GENERIC *** [card=0,autodetected]
bttv0: gpio: en=00000000, out=00000000 in=00ffffff [init]
bt878: Unknown symbol bttv_read_gpio
bt878: Unknown symbol bttv_write_gpio
bt878: Unknown symbol bttv_gpio_enable
ACPI: PCI Interrupt Link [LAZA] enabled at IRQ 11
ACPI: PCI Interrupt 0000:00:05.0 -> Link [LAZA] -> GSI 11 (level, low) -> IRQ 11
PCI: Setting latency timer of device 0000:00:05.0 to 64
hda_codec: Unknown model for ALC662, trying auto-probe from BIOS...
hda_codec: num_steps = 0 for NID=0xc
tveeprom 2-0050: Huh, no eeprom present (err=-121)?
bttv0: tuner type unset
bttv0: i2c: checking for MSP34xx @ 0x80... not found
bttv0: i2c: checking for TDA9875 @ 0xb0... not found
bttv0: i2c: checking for TDA7432 @ 0x8a... not found
bttv0: registered device video0
bttv0: registered device vbi0
bttv: Bt8xx card found (1).
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 10
ACPI: PCI Interrupt 0000:02:09.0[A] -> Link [LNKC] -> GSI 10 (level, low) -> IRQ 10
bttv1: Bt878 (rev 17) at 0000:02:09.0, irq: 10, latency: 64, mmio: 0xbfffd000
bttv1: using: *** UNKNOWN/GENERIC *** [card=0,autodetected]
bttv1: gpio: en=00000000, out=00000000 in=00ffffff [init]
hda_codec: num_steps = 0 for NID=0xc
hda_codec: num_steps = 0 for NID=0xc
hda_codec: num_steps = 0 for NID=0xc
hda_codec: num_steps = 0 for NID=0xc
tveeprom 3-0050: Huh, no eeprom present (err=-121)?
bttv1: tuner type unset
bttv1: i2c: checking for MSP34xx @ 0x80... not found
bttv1: i2c: checking for TDA9875 @ 0xb0... not found
bttv1: i2c: checking for TDA7432 @ 0x8a... not found
bttv1: registered device video1
bttv1: registered device vbi1
bttv: Bt8xx card found (2).
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11
ACPI: PCI Interrupt 0000:02:0a.0[A] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11
bttv2: Bt878 (rev 17) at 0000:02:0a.0, irq: 11, latency: 64, mmio: 0xbfffb000
bttv2: using: *** UNKNOWN/GENERIC *** [card=0,autodetected]
bttv2: gpio: en=00000000, out=00000000 in=00ffffff [init]
tveeprom 4-0050: Huh, no eeprom present (err=-121)?
bttv2: tuner type unset
bttv2: i2c: checking for MSP34xx @ 0x80... not found
bttv2: i2c: checking for TDA9875 @ 0xb0... not found
bttv2: i2c: checking for TDA7432 @ 0x8a... not found
bttv2: registered device video2
bttv2: registered device vbi2
bttv: Bt8xx card found (3).
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
ACPI: PCI Interrupt 0000:02:0b.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
bttv3: Bt878 (rev 17) at 0000:02:0b.0, irq: 11, latency: 64, mmio: 0xbfff9000
bttv3: using: *** UNKNOWN/GENERIC *** [card=0,autodetected]
bttv3: gpio: en=00000000, out=00000000 in=00ffffff [init]
tveeprom 5-0050: Huh, no eeprom present (err=-121)?
bttv3: tuner type unset
bttv3: i2c: checking for MSP34xx @ 0x80... not found
bttv3: i2c: checking for TDA9875 @ 0xb0... not found
bttv3: i2c: checking for TDA7432 @ 0x8a... not found
bttv3: registered device video3
bttv3: registered device vbi3
bttv: Bt8xx card found (4).
ACPI: PCI Interrupt 0000:02:0c.0[A] -> Link [LNKB] -> GSI 11 (level, low) -> IRQ 11
bttv4: Bt878 (rev 17) at 0000:02:0c.0, irq: 11, latency: 64, mmio: 0xbfff7000
bttv4: using: *** UNKNOWN/GENERIC *** [card=0,autodetected]
bttv4: gpio: en=00000000, out=00000000 in=00ffffff [init]
tveeprom 6-0050: Huh, no eeprom present (err=-121)?
bttv4: tuner type unset
bttv4: i2c: checking for MSP34xx @ 0x80... not found
bttv4: i2c: checking for TDA9875 @ 0xb0... not found
bttv4: i2c: checking for TDA7432 @ 0x8a... not found
bttv4: registered device video4
bttv4: registered device vbi4
bttv: Bt8xx card found (5).
ACPI: PCI Interrupt 0000:02:0d.0[A] -> Link [LNKC] -> GSI 10 (level, low) -> IRQ 10
bttv5: Bt878 (rev 17) at 0000:02:0d.0, irq: 10, latency: 64, mmio: 0xbfff5000
bttv5: using: *** UNKNOWN/GENERIC *** [card=0,autodetected]
bttv5: gpio: en=00000000, out=00000000 in=00ffffff [init]
tveeprom 7-0050: Huh, no eeprom present (err=-121)?
bttv5: tuner type unset
bttv5: i2c: checking for MSP34xx @ 0x80... not found
bttv5: i2c: checking for TDA9875 @ 0xb0... not found
bttv5: i2c: checking for TDA7432 @ 0x8a... not found
bttv5: registered device video5
bttv5: registered device vbi5
bttv: Bt8xx card found (6).
ACPI: PCI Interrupt 0000:02:0e.0[A] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11
bttv6: Bt878 (rev 17) at 0000:02:0e.0, irq: 11, latency: 64, mmio: 0xbfff3000
bttv6: using: *** UNKNOWN/GENERIC *** [card=0,autodetected]
bttv6: gpio: en=00000000, out=00000000 in=00ffffff [init]
tveeprom 8-0050: Huh, no eeprom present (err=-121)?
bttv6: tuner type unset
bttv6: i2c: checking for MSP34xx @ 0x80... not found
bttv6: i2c: checking for TDA9875 @ 0xb0... not found
bttv6: i2c: checking for TDA7432 @ 0x8a... not found
bttv6: registered device video6
bttv6: registered device vbi6
bttv: Bt8xx card found (7).
ACPI: PCI Interrupt 0000:02:0f.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
bttv7: Bt878 (rev 17) at 0000:02:0f.0, irq: 11, latency: 64, mmio: 0xbfff1000
bttv7: using: *** UNKNOWN/GENERIC *** [card=0,autodetected]
bttv7: gpio: en=00000000, out=00000000 in=00ffffff [init]
tveeprom 9-0050: Huh, no eeprom present (err=-121)?
bttv7: tuner type unset
bttv7: i2c: checking for MSP34xx @ 0x80... not found
bttv7: i2c: checking for TDA9875 @ 0xb0... not found
bttv7: i2c: checking for TDA7432 @ 0x8a... not found
bttv7: registered device video7
bttv7: registered device vbi7
bt878: AUDIO driver version 0.0.0 loaded
bt878: Bt878 AUDIO function found (0).
ACPI: PCI Interrupt 0000:02:08.1[A] -> Link [LNKB] -> GSI 11 (level, low) -> IRQ 11
bt878_probe: card id=[0x0], Unknown card.
Exiting..
ACPI: PCI interrupt for device 0000:02:08.1 disabled
bt878: probe of 0000:02:08.1 failed with error -22
bt878: Bt878 AUDIO function found (0).
ACPI: PCI Interrupt 0000:02:09.1[A] -> Link [LNKC] -> GSI 10 (level, low) -> IRQ 10
bt878_probe: card id=[0x0], Unknown card.
Exiting..
ACPI: PCI interrupt for device 0000:02:09.1 disabled
bt878: probe of 0000:02:09.1 failed with error -22
bt878: Bt878 AUDIO function found (0).
ACPI: PCI Interrupt 0000:02:0a.1[A] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11
bt878_probe: card id=[0x0], Unknown card.
Exiting..
ACPI: PCI interrupt for device 0000:02:0a.1 disabled
bt878: probe of 0000:02:0a.1 failed with error -22
bt878: Bt878 AUDIO function found (0).
ACPI: PCI Interrupt 0000:02:0b.1[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
bt878_probe: card id=[0x0], Unknown card.
Exiting..
ACPI: PCI interrupt for device 0000:02:0b.1 disabled
bt878: probe of 0000:02:0b.1 failed with error -22
bt878: Bt878 AUDIO function found (0).
ACPI: PCI Interrupt 0000:02:0c.1[A] -> Link [LNKB] -> GSI 11 (level, low) -> IRQ 11
bt878_probe: card id=[0x0], Unknown card.
Exiting..
ACPI: PCI interrupt for device 0000:02:0c.1 disabled
bt878: probe of 0000:02:0c.1 failed with error -22
bt878: Bt878 AUDIO function found (0).
ACPI: PCI Interrupt 0000:02:0d.1[A] -> Link [LNKC] -> GSI 10 (level, low) -> IRQ 10
bt878_probe: card id=[0x0], Unknown card.
Exiting..
ACPI: PCI interrupt for device 0000:02:0d.1 disabled
bt878: probe of 0000:02:0d.1 failed with error -22
bt878: Bt878 AUDIO function found (0).
ACPI: PCI Interrupt 0000:02:0e.1[A] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11
bt878_probe: card id=[0x0], Unknown card.
Exiting..
ACPI: PCI interrupt for device 0000:02:0e.1 disabled
bt878: probe of 0000:02:0e.1 failed with error -22
bt878: Bt878 AUDIO function found (0).
ACPI: PCI Interrupt 0000:02:0f.1[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
bt878_probe: card id=[0x0], Unknown card.
Exiting..
ACPI: PCI interrupt for device 0000:02:0f.1 disabled
bt878: probe of 0000:02:0f.1 failed with error -22
Still don<t know how to solve the problem?
Here`s the result of xawtv -hwscan
This is xawtv-3.95, running on Linux/i686 (2.6.23.12-52.fc7)
looking for available devices
port 355-386
type : Xvideo, image scaler
name : NV17 Video Texture
port 387-418
type : Xvideo, image scaler
name : NV05 Video Blitter
/dev/video0: OK [ -device /dev/video0 ]
type : v4l2
name : BT878 video ( *** UNKNOWN/GENER
flags: overlay capture tuner
/dev/video1: OK [ -device /dev/video1 ]
type : v4l2
name : BT878 video ( *** UNKNOWN/GENER
flags: overlay capture tuner
/dev/video2: OK [ -device /dev/video2 ]
type : v4l2
name : BT878 video ( *** UNKNOWN/GENER
flags: overlay capture tuner
/dev/video3: OK [ -device /dev/video3 ]
type : v4l2
name : BT878 video ( *** UNKNOWN/GENER
flags: overlay capture tuner
This is xawtv-3.95, running on Linux/i686 (2.6.23.12-52.fc7)
looking for available devices
port 355-386
type : Xvideo, image scaler
name : NV17 Video Texture
port 387-418
type : Xvideo, image scaler
name : NV05 Video Blitter
/dev/video0: OK [ -device /dev/video0 ]
type : v4l2
name : BT878 video ( *** UNKNOWN/GENER
flags: overlay capture tuner
/dev/video1: OK [ -device /dev/video1 ]
type : v4l2
name : BT878 video ( *** UNKNOWN/GENER
flags: overlay capture tuner
/dev/video2: OK [ -device /dev/video2 ]
type : v4l2
name : BT878 video ( *** UNKNOWN/GENER
flags: overlay capture tuner
/dev/video3: OK [ -device /dev/video3 ]
type : v4l2
name : BT878 video ( *** UNKNOWN/GENER
flags: overlay capture tuner
Add this to /etc/modprobe.d/options
It may work. If not, you will need to find out what your card needs.
It may work. If not, you will need to find out what your card needs.
Code: Select all
options i2c_algo_bit bit_test=1
options bttv gbuffers=16 radio=-1 tuner=4 card=102,102,102,102,102,102,102,102Kodicom 8800 seems to be difficult to work with!!!
I add these options above in /etc/modprobe.d/options and also try some others, they all seems to do the same thing. Got video on /dev/video0 as long as I don<t add another monitor. If I add /dev/video1, everything stop working.
zmu -d /dev/video0 -q -v:
Video Capabilities
Name: BT878 video (IVC-200)
Type: 171
Can capture
Can tune
Overlay onto frame buffer
Can clip
Scalable
Video Channels: 1
Audio Channels: 0
Maximum Width: 768
Maximum Height: 480
Minimum Width: 48
Minimum Height: 32
Window Attributes
X Offset: 0
Y Offset: 0
Width: 352
Height: 288
Picture Attributes
Palette: 4 - 24bit RGB
Colour Depth: 24
Brightness: 32768
Hue: 32768
Colour :32768
Contrast: 32768
Whiteness: 0
Channel 0 Attributes
Name: Composite0
Channel: 0
Flags: 2
Channel has audio
Type: 2 - Camera
Format: 1 - NTSC
zmu -d /dev/video0 -q -v:
Video Capabilities
Name: BT878 video (IVC-200)
Type: 171
Can capture
Can tune
Overlay onto frame buffer
Can clip
Scalable
Video Channels: 1
Audio Channels: 0
Maximum Width: 768
Maximum Height: 480
Minimum Width: 48
Minimum Height: 32
Window Attributes
X Offset: 0
Y Offset: 0
Width: 352
Height: 288
Picture Attributes
Palette: 4 - 24bit RGB
Colour Depth: 24
Brightness: 32768
Hue: 32768
Colour :32768
Contrast: 32768
Whiteness: 0
Channel 0 Attributes
Name: Composite0
Channel: 0
Flags: 2
Channel has audio
Type: 2 - Camera
Format: 1 - NTSC
Still the same problem!
I try different capture board to see if I was doing something wrong. The best results I got came from the KODICOM 8800.
I still got video on /dev/video0 but the blue screen still remain on all other inputs.
I try many card configuration options. (102... - 171... - 105...)
Xawtv -hw scan returns me only 4 inputs while -zmu returns me input 0 to 7.
I'm confident that I'm not far from getting video on all inputs.
if anybody got an amazing idea please reply or contact me!
Thank you!
I still got video on /dev/video0 but the blue screen still remain on all other inputs.
I try many card configuration options. (102... - 171... - 105...)
Xawtv -hw scan returns me only 4 inputs while -zmu returns me input 0 to 7.
I'm confident that I'm not far from getting video on all inputs.
if anybody got an amazing idea please reply or contact me!
Thank you!