again, trouble with kodicom 8800 clone and slackware 12

sugacapra · Post by **sugacapra** » Tue Feb 12, 2008 4:36 pm

damn me,
probably i was burned, a little tired after this marathon of 20 hours on
this F#@king delicius asus barebone

but ok, i resolve all the issue about installing zm on slack12,
but appear that the gremlin on my back is always alive and kicking..

some info useful for debug (or help):

root@videoserver:~# cat /proc/interrupts
CPU0
0: 142804 XT-PIC-XT timer
1: 2 XT-PIC-XT i8042
2: 0 XT-PIC-XT cascade
3: 125 XT-PIC-XT ohci1394, bttv3, bttv7, bt878
5: 108 XT-PIC-XT ATI IXP, bttv0, bttv4, bt878
7: 2 XT-PIC-XT parport0
8: 1 XT-PIC-XT rtc
9: 1 XT-PIC-XT acpi
10: 94 XT-PIC-XT ehci_hcd:usb1, ohci_hcd:usb2, ohci_hcd:usb3, bttv2, bttv6, bt878
11: 2032 XT-PIC-XT yenta, bttv1, bttv5, bt878, eth0
12: 4 XT-PIC-XT i8042
14: 22426 XT-PIC-XT ide0
NMI: 0
ERR: 0

root@videoserver:~# lsmod
Module Size Used by
snd_seq_dummy 2692 0
snd_seq_oss 28032 0
snd_seq_midi_event 5888 1 snd_seq_oss
snd_seq 42576 5 snd_seq_dummy,snd_seq_oss,snd_seq_midi_event
snd_seq_device 6540 3 snd_seq_dummy,snd_seq_oss,snd_seq
snd_pcm_oss 38432 0
snd_mixer_oss 13824 1 snd_pcm_oss
ipv6 226016 28
capability 3336 0
commoncap 5376 1 capability
lp 9800 0
bt878 8872 0
parport_pc 23844 1
parport 30152 2 lp,parport_pc
pcspkr 2304 0
psmouse 34440 0
pcmcia 30628 0
bttv 168436 1 bt878
video_buf 20228 1 bttv
ir_common 29956 1 bttv
compat_ioctl32 1280 1 bttv
btcx_risc 3976 1 bttv
tveeprom 13712 1 bttv
videodev 25344 1 bttv
v4l2_common 14848 2 bttv,videodev
v4l1_compat 13700 2 bttv,videodev
yenta_socket 23180 1
rsrc_nonstatic 10880 1 yenta_socket
serio_raw 5124 0
pcmcia_core 32400 3 pcmcia,yenta_socket,rsrc_nonstatic
8139too 20864 0
mii 4736 1 8139too
ati_agp 6924 1
i2c_piix4 7436 0
shpchp 29204 0
agpgart 26928 1 ati_agp
ata_generic 5252 0
evdev 7936 0
pata_atiixp 5504 0
snd_atiixp 15116 0
snd_ac97_codec 96292 1 snd_atiixp
ac97_bus 2048 1 snd_ac97_codec
snd_pcm 65160 3 snd_pcm_oss,snd_atiixp,snd_ac97_codec
snd_timer 17540 2 snd_seq,snd_pcm
snd 41956 9 snd_seq_oss,snd_seq,snd_seq_device,snd_pcm_oss,snd_mixer_oss,snd_atiixp,snd_ac97_codec,snd_pcm,snd_timer
soundcore 5728 1 snd
snd_page_alloc 7432 2 snd_atiixp,snd_pcm

lspci -v
00:00.0 Host bridge: ATI Technologies Inc Radeon 9100 IGP Host Bridge
Subsystem: ASUSTeK Computer Inc. Unknown device 8107
Flags: bus master, 66MHz, medium devsel, latency 64
Memory at f0000000 (32-bit, prefetchable)
Memory at feb00000 (32-bit, non-prefetchable)
Capabilities: [a0] AGP version 3.0

00:01.0 PCI bridge: ATI Technologies Inc Radeon 9100 IGP PCI/AGP Bridge (prog-if
00 [Normal decode])
Flags: bus master, 66MHz, medium devsel, latency 64
Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: fd900000-fdcfffff
Prefetchable memory behind bridge: dde00000-eddfffff

00:13.0 USB Controller: ATI Technologies Inc OHCI USB Controller #1 (rev 01) (pr
og-if 10 [OHCI])
Subsystem: ASUSTeK Computer Inc. Unknown device 8108
Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 10
Memory at fe800000 (32-bit, non-prefetchable)

00:13.1 USB Controller: ATI Technologies Inc OHCI USB Controller #2 (rev 01) (pr
og-if 10 [OHCI])
Subsystem: ASUSTeK Computer Inc. Unknown device 8108
Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 10
Memory at fe900000 (32-bit, non-prefetchable)

00:13.2 USB Controller: ATI Technologies Inc EHCI USB Controller (rev 01) (prog-
if 20 [EHCI])
Subsystem: ASUSTeK Computer Inc. Unknown device 8108
Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 10
Memory at fea00000 (32-bit, non-prefetchable)
Capabilities: [dc] Power Management version 2

00:14.0 SMBus: ATI Technologies Inc SMBus (rev 18)
Subsystem: ASUSTeK Computer Inc. Unknown device 8108
Flags: 66MHz, medium devsel
I/O ports at 0a00
Memory at 40000000 (32-bit, non-prefetchable)

00:14.1 IDE interface: ATI Technologies Inc Dual Channel Bus Master PCI IDE Cont
roller (prog-if 8a [Master SecP PriP])
Subsystem: ASUSTeK Computer Inc. Unknown device 8108
Flags: bus master, medium devsel, latency 0, IRQ 11
I/O ports at 01f0
I/O ports at 03f4

00:14.3 ISA bridge: ATI Technologies Inc Unknown device 434c
Subsystem: ASUSTeK Computer Inc. Unknown device 8108
Flags: bus master, 66MHz, medium devsel, latency 0

00:14.4 PCI bridge: ATI Technologies Inc Unknown device 4342 (prog-if 01 [Subtractive decode])
Flags: bus master, 66MHz, medium devsel, latency 64
Bus: primary=00, secondary=02, subordinate=08, sec-latency=64
I/O behind bridge: 00001000-00001fff
Memory behind bridge: fdd00000-fe0fffff
Prefetchable memory behind bridge: ede00000-efdfffff

00:14.5 Multimedia audio controller: ATI Technologies Inc IXP150 AC'97 Audio Controller
Subsystem: ASUSTeK Computer Inc. Unknown device 810d
Flags: bus master, 66MHz, slow devsel, latency 64, IRQ 5
Memory at fe700000 (32-bit, non-prefetchable)

01:05.0 VGA compatible controller: ATI Technologies Inc Radeon 9100 PRO IGP (prog-if 00 [VGA])
Subsystem: ASUSTeK Computer Inc. Unknown device 8107
Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 11
Memory at e0000000 (32-bit, prefetchable) [size=128M]
I/O ports at d000 [size=256]
Memory at fdc00000 (32-bit, non-prefetchable) [size=64K]

Expansion ROM at fdb00000 [disabled] [size=128K]
Capabilities: [58] AGP version 3.0
Capabilities: [50] Power Management version 2

02:09.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
Subsystem: Realtek Semiconductor Co., Ltd. RT8139
Flags: bus master, medium devsel, latency 64, IRQ 11
I/O ports at e800 [size=256]
Memory at fe000000 (32-bit, non-prefetchable) [size=256]
Capabilities: [50] Power Management version 2

02:0a.0 FireWire (IEEE 1394): VIA Technologies, Inc. IEEE 1394 Host Controller (rev 80) (prog-if
10 [OHCI])
Subsystem: ASUSTeK Computer Inc. A8V Deluxe or A8N-VM CSM Mainboard
Flags: bus master, medium devsel, latency 64, IRQ 3
Memory at fdf00000 (32-bit, non-prefetchable) [size=2K]
I/O ports at ec00 [size=128]
Capabilities: [50] Power Management version 2

02:0c.0 CardBus bridge: ENE Technology Inc CB-710/2/4 Cardbus Controller (rev 02)
Subsystem: ASUSTeK Computer Inc. Unknown device 8131
Flags: bus master, medium devsel, latency 168, IRQ 11
Memory at fdd00000 (32-bit, non-prefetchable) [size=4K]

Bus: primary=02, secondary=05, subordinate=08, sec-latency=176
Memory window 0: 44000000-47fff000 (prefetchable)
Memory window 1: 48000000-4bfff000
I/O window 0: 00001000-000010ff
I/O window 1: 00001400-000014ff
16-bit legacy interface ports at 0001

02:0c.1 FLASH memory: ENE Technology Inc CB710 Memory Card Reader Controller
Subsystem: ASUSTeK Computer Inc. Unknown device 1724
Flags: medium devsel, IRQ 10
I/O ports at e480 [size=128]
Capabilities: [a0] Power Management version 2

02:0e.0 PCI bridge: Hint Corp HiNT HB4 PCI-PCI Bridge (PCI6150) (rev 04) (prog-if 00 [Normal dec
ode])
Flags: bus master, medium devsel, latency 64
Bus: primary=02, secondary=04, subordinate=04, sec-latency=64
Prefetchable memory behind bridge: 00000000ede00000-00000000efdfffff
Capabilities: [dc] Power Management version 1
Capabilities: [e4] #06 [0094]
Capabilities: [e8] Vital Product Data

04:08.0 Multimedia video controller: Brooktree Corporation Bt878 Video Capture (rev 11)
Flags: bus master, medium devsel, latency 64, IRQ 5
Memory at efc00000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2

04:08.1 Multimedia controller: Brooktree Corporation Bt878 Audio Capture (rev 11)
Flags: bus master, medium devsel, latency 64, IRQ 5
Memory at efd00000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2

04:09.0 Multimedia video controller: Brooktree Corporation Bt878 Video Capture (rev 11)
Flags: bus master, medium devsel, latency 64, IRQ 11
Memory at efa00000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2

04:09.1 Multimedia controller: Brooktree Corporation Bt878 Audio Capture (rev 11)
Flags: bus master, medium devsel, latency 64, IRQ 11
Memory at efb00000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2

04:0a.0 Multimedia video controller: Brooktree Corporation Bt878 Video Capture (rev 11)
Flags: bus master, medium devsel, latency 64, IRQ 10
Memory at ef800000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2

04:0a.1 Multimedia controller: Brooktree Corporation Bt878 Audio Capture (rev 11)
Flags: bus master, medium devsel, latency 64, IRQ 10
Memory at ef900000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2

04:0b.0 Multimedia video controller: Brooktree Corporation Bt878 Video Capture (rev 11)
Flags: bus master, medium devsel, latency 64, IRQ 3
Memory at ef600000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2

04:0b.1 Multimedia controller: Brooktree Corporation Bt878 Audio Capture (rev 11)
Flags: bus master, medium devsel, latency 64, IRQ 3
Memory at ef700000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2

04:0c.0 Multimedia video controller: Brooktree Corporation Bt878 Video Capture (rev 11)
Flags: bus master, medium devsel, latency 64, IRQ 5
Memory at ef400000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2

04:0c.1 Multimedia controller: Brooktree Corporation Bt878 Audio Capture (rev 11)
Flags: bus master, medium devsel, latency 64, IRQ 5
Memory at ef500000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2

04:0d.0 Multimedia video controller: Brooktree Corporation Bt878 Video Capture (rev 11)
Flags: bus master, medium devsel, latency 64, IRQ 11
Memory at ef200000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2

04:0d.1 Multimedia controller: Brooktree Corporation Bt878 Audio Capture (rev 11)
Flags: bus master, medium devsel, latency 64, IRQ 11
Memory at ef300000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data

Capabilities: [4c] Power Management version 2

04:0e.0 Multimedia video controller: Brooktree Corporation Bt878 Video Capture (rev 11)
Flags: bus master, medium devsel, latency 64, IRQ 10
Memory at ef000000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2

04:0e.1 Multimedia controller: Brooktree Corporation Bt878 Audio Capture (rev 11)
Flags: bus master, medium devsel, latency 64, IRQ 10
Memory at ef100000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2

04:0f.0 Multimedia video controller: Brooktree Corporation Bt878 Video Capture (rev 11)
Flags: bus master, medium devsel, latency 64, IRQ 3
Memory at eee00000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2

04:0f.1 Multimedia controller: Brooktree Corporation Bt878 Audio Capture (rev 11)
Flags: bus master, medium devsel, latency 64, IRQ 3
Memory at eef00000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2

------------------------

the card is in modprobe
as 102,102,102,102,102,102,102,102

but something goes wrong cause i've black screens and not blue one..

somene can help?

Post by **cordel** » Tue Feb 12, 2008 8:04 pm

Have you verified that the card is loading correctly?
dmesg |grep bttv

sugacapra · Post by **sugacapra** » Tue Feb 12, 2008 9:37 pm

Hi Cordel, and thanks for the answer,
i use this card on a previous zm installation (and it work perfectly for about 1 year and half) defining in modprobe options tuner=-1 radio=-1 card=77,77,77,77,77,77,77,77

the dev videos work all (on prev. installation)

now, i read on some post here that this card work better with 8x 102's card,
but now i'm not so sure, appear that the boot was very very long (more than 2 mins) and what leave me stoned is the presence of "audio capture devices",
that i've not for sure.
Now i can't try again till tomorrow (i leave the server on final site and still not yet implemented the remote connection, to save this night to me, cause i'm a bit tired now

)
Maybe is the V4L2 that is different (on prev. i used the old V4L )

but definitely i will force this card to work, want it or not i need to restart the video surveillance there.

Tomorrow i try to reset to 77 the card type.

and post the result.
best wishes

Post by **cordel** » Tue Feb 12, 2008 10:03 pm

Some input from the logs might be useful.

sugacapra · Post by **sugacapra** » Wed Feb 13, 2008 6:47 am

here the
dmesg | grep bttv

result.. maybe there is some trouble here..

bttv: driver version 0.9.17 loaded
bttv: using 8 buffers with 2080k (520 pages) each for capture
bttv: Bt8xx card found (0).
bttv0: Bt878 (rev 17) at 0000:04:08.0, irq: 5, latency: 64, mmio: 0xefc00000
bttv0: using: IVC-200 [card=102,insmod option]
bttv0: gpio: en=00000000, out=00000000 in=00ffffff [init]
bt878: Unknown symbol bttv_read_gpio
bt878: Unknown symbol bttv_write_gpio
bt878: Unknown symbol bttv_gpio_enable
bt878: Unknown symbol bttv_read_gpio
bt878: Unknown symbol bttv_write_gpio
bt878: Unknown symbol bttv_gpio_enable
bt878: Unknown symbol bttv_read_gpio
bt878: Unknown symbol bttv_write_gpio
bt878: Unknown symbol bttv_gpio_enable
bt878: Unknown symbol bttv_read_gpio
bt878: Unknown symbol bttv_write_gpio
bt878: Unknown symbol bttv_gpio_enable
bttv0: using tuner=-1
bttv0: i2c: checking for MSP34xx @ 0x80... not found
bttv0: i2c: checking for TDA9875 @ 0xb0... not found
bttv0: i2c: checking for TDA7432 @ 0x8a... not found
bttv0: i2c: checking for TDA9887 @ 0x86... <6>cs: IO port probe 0xc00-0xcff: excluding 0xc00-0xc07 0xc10-0xc17 0xc50-0xc57 0xc68-0xc6f 0xcd0-0xcd7
bttv0: registered device video0
bttv0: registered device vbi0
bttv0: registered device radio0
bttv0: PLL: 28636363 => 35468950 .. ok
bttv: Bt8xx card found (1).
bttv1: Bt878 (rev 17) at 0000:04:09.0, irq: 11, latency: 64, mmio: 0xefa00000
bttv1: using: IVC-200 [card=102,insmod option]
bttv1: gpio: en=00000000, out=00000000 in=00ffffff [init]
bttv1: using tuner=-1
bttv1: i2c: checking for MSP34xx @ 0x80... not found
bttv1: i2c: checking for TDA9875 @ 0xb0... not found
bttv1: i2c: checking for TDA7432 @ 0x8a... not found
bttv1: i2c: checking for TDA9887 @ 0x86... not found
bttv1: registered device video1
bttv1: registered device vbi1
bttv1: PLL: 28636363 => 35468950 .. ok
bttv: Bt8xx card found (2).
bttv2: Bt878 (rev 17) at 0000:04:0a.0, irq: 10, latency: 64, mmio: 0xef800000
bttv2: using: IVC-200 [card=102,insmod option]
bttv2: gpio: en=00000000, out=00000000 in=00ffffff [init]
bttv2: using tuner=-1
bttv2: i2c: checking for MSP34xx @ 0x80... not found
bttv2: i2c: checking for TDA9875 @ 0xb0... not found
bttv2: i2c: checking for TDA7432 @ 0x8a... not found
bttv2: i2c: checking for TDA9887 @ 0x86... not found
bttv2: registered device video2
bttv2: registered device vbi2
bttv2: PLL: 28636363 => 35468950 .. ok
bttv: Bt8xx card found (3).
bttv3: Bt878 (rev 17) at 0000:04:0b.0, irq: 3, latency: 64, mmio: 0xef600000
bttv3: using: IVC-200 [card=102,insmod option]
bttv3: gpio: en=00000000, out=00000000 in=00ffffff [init]
bttv3: using tuner=-1
bttv3: i2c: checking for MSP34xx @ 0x80... not found
bttv3: i2c: checking for TDA9875 @ 0xb0... not found
bttv3: i2c: checking for TDA7432 @ 0x8a... <6>Adding 4915848k swap on /dev/hdb5. Priority:-1 extents:1 across:4915848k
bttv3: i2c: checking for TDA9887 @ 0x86... not found
bttv3: registered device video3
bttv3: registered device vbi3
bttv3: PLL: 28636363 => 35468950 .. ok
bttv: Bt8xx card found (4).
bttv4: Bt878 (rev 17) at 0000:04:0c.0, irq: 5, latency: 64, mmio: 0xef400000
bttv4: using: IVC-200 [card=102,insmod option]
bttv4: gpio: en=00000000, out=00000000 in=00ffffff [init]
bttv4: using tuner=-1
bttv4: i2c: checking for MSP34xx @ 0x80... not found
bttv4: i2c: checking for TDA9875 @ 0xb0... not found
bttv4: i2c: checking for TDA7432 @ 0x8a... not found
bttv4: i2c: checking for TDA9887 @ 0x86... <6>input: PC Speaker as /class/input/input1
bttv4: registered device video4
bttv4: registered device vbi4
bttv4: PLL: 28636363 => 35468950 .. ok
bttv: Bt8xx card found (5).
bttv5: Bt878 (rev 17) at 0000:04:0d.0, irq: 11, latency: 64, mmio: 0xef200000
bttv5: using: IVC-200 [card=102,insmod option]
bttv5: gpio: en=00000000, out=00000000 in=00ffffff [init]
bttv5: using tuner=-1
bttv5: i2c: checking for MSP34xx @ 0x80... not found
bttv5: i2c: checking for TDA9875 @ 0xb0... not found
bttv5: i2c: checking for TDA7432 @ 0x8a... not found
bttv5: i2c: checking for TDA9887 @ 0x86... not found
bttv5: registered device video5
bttv5: registered device vbi5
bttv5: PLL: 28636363 => 35468950 .. ok
bttv: Bt8xx card found (6).
bttv6: Bt878 (rev 17) at 0000:04:0e.0, irq: 10, latency: 64, mmio: 0xef000000
bttv6: using: IVC-200 [card=102,insmod option]
bttv6: gpio: en=00000000, out=00000000 in=00ffffff [init]
bttv6: using tuner=-1
bttv6: i2c: checking for MSP34xx @ 0x80... not found
bttv6: i2c: checking for TDA9875 @ 0xb0... not found
bttv6: i2c: checking for TDA7432 @ 0x8a... not found
bttv6: i2c: checking for TDA9887 @ 0x86... not found
bttv6: registered device video6
bttv6: registered device vbi6
bttv6: PLL: 28636363 => 35468950 .. ok
bttv: Bt8xx card found (7).
bttv7: Bt878 (rev 17) at 0000:04:0f.0, irq: 3, latency: 64, mmio: 0xeee00000
bttv7: using: IVC-200 [card=102,insmod option]
bttv7: gpio: en=00000000, out=00000000 in=00ffffff [init]
bttv7: using tuner=-1
bttv7: i2c: checking for MSP34xx @ 0x80... not found
bttv7: i2c: checking for TDA9875 @ 0xb0... not found
bttv7: i2c: checking for TDA7432 @ 0x8a... not found
bttv7: i2c: checking for TDA9887 @ 0x86... not found
bttv7: registered device video7
bttv7: registered device vbi7
bttv7: PLL: 28636363 => 35468950 .. ok
bttv1: timeout: drop=0 irq=30/90, risc=3763d010, bits: HSYNC
bttv1: reset, reinitialize
bttv1: PLL: 28636363 => 35468950 . ok
bttv0: timeout: drop=0 irq=29/30, risc=376ad000, bits: HSYNC
bttv0: reset, reinitialize
bttv0: PLL: 28636363 => 35468950 . ok
bttv2: timeout: drop=0 irq=32/33, risc=37599000, bits: HSYNC
bttv2: reset, reinitialize
bttv2: PLL: 28636363 => 35468950 . ok
bttv1: timeout: drop=0 irq=34/94, risc=3763d000, bits: VSYNC HSYNC
bttv0: timeout: drop=0 irq=32/52, risc=376ad000, bits: VSYNC HSYNC
bttv4: timeout: drop=0 irq=28/59, risc=37304000, bits: HSYNC
bttv4: reset, reinitialize
bttv4: PLL: 28636363 => 35468950 . ok
bttv2: timeout: drop=0 irq=33/34, risc=37599000, bits: VSYNC HSYNC
bttv5: timeout: drop=0 irq=29/123, risc=36d39000, bits: HSYNC
bttv5: reset, reinitialize
bttv5: PLL: 28636363 => 35468950 . ok
bttv4: timeout: drop=0 irq=31/62, risc=37304000, bits: VSYNC HSYNC
bttv6: timeout: drop=0 irq=29/59, risc=37235000, bits: HSYNC
bttv6: reset, reinitialize
bttv6: PLL: 28636363 => 35468950 . ok
bttv5: timeout: drop=0 irq=32/126, risc=36d39000, bits: VSYNC HSYNC
bttv7: timeout: drop=0 irq=28/37, risc=37705000, bits: HSYNC
bttv7: reset, reinitialize
bttv7: PLL: 28636363 => 35468950 . ok
bttv6: timeout: drop=0 irq=32/62, risc=37235000, bits: VSYNC HSYNC
bttv3: timeout: drop=0 irq=31/62, risc=3708a000, bits: HSYNC
bttv3: reset, reinitialize
bttv3: PLL: 28636363 => 35468950 . ok
bttv7: timeout: drop=0 irq=31/60, risc=37705000, bits: VSYNC HSYNC
bttv3: timeout: drop=0 irq=32/63, risc=3708a000, bits: VSYNC HSYNC
bttv0: reset, reinitialize
bttv0: PLL: 28636363 => 35468950 .<6>bttv2: reset, reinitialize
bttv2: PLL: 28636363 => 35468950 . ok
bttv1: reset, reinitialize
bttv1: PLL: 28636363 => 35468950 . ok
bttv2: timeout: drop=0 irq=34/66, risc=37599000, bits: VSYNC HSYNC
bttv0: timeout: drop=0 irq=35/66, risc=376ad000, bits: VSYNC HSYNC
bttv1: timeout: drop=0 irq=37/172, risc=3763d000, bits: VSYNC HSYNC
bttv4: reset, reinitialize
bttv4: PLL: 28636363 => 35468950 .<6>bttv6: reset, reinitialize
bttv6: PLL: 28636363 => 35468950 . ok
bttv5: reset, reinitialize
bttv5: PLL: 28636363 => 35468950 . ok
bttv4: timeout: drop=0 irq=34/68, risc=37304000, bits: VSYNC HSYNC
bttv5: timeout: drop=0 irq=35/190, risc=36d39000, bits: VSYNC HSYNC
bttv6: timeout: drop=0 irq=35/66, risc=37235000, bits: VSYNC HSYNC
bttv3: reset, reinitialize
bttv3: PLL: 28636363 => 35468950 . ok
bttv7: reset, reinitialize
bttv7: PLL: 28636363 => 35468950 . ok
bttv3: timeout: drop=0 irq=33/67, risc=3708a000, bits: VSYNC HSYNC
bttv7: timeout: drop=0 irq=34/64, risc=37705000, bits: VSYNC HSYNC

Lee Sharp · Post by **Lee Sharp** » Wed Feb 13, 2008 3:17 pm

For the delay, add this to the options file.

Code: Select all

options i2c_algo_bit bit_test=1

The audio is normal as it is in the chip, but usually not implemented.
This is the other line I add for my card.

Code: Select all

options bttv gbuffers=16 radio=-1 tuner=4 card=102,102,102,102,102,102,102,102

It is a Chinese clone...

sugacapra · Post by **sugacapra** » Sat Feb 16, 2008 1:04 pm

hi there, i've tested the suggestion
on /etc/modprobe.d/modprobe.conf

options i2c_algo_bit bit_test=1
options bttv gbuffers=16 radio=-1 tuner=4 card=102,102,102,102,102,102,102,102

and also the combo

options i2c_algo_bit bit_test=1
options bttv gbuffers=16 radio=-1 card=77,77,77,77,77,77,77,77

cause in my last installation this card (a kodicom8800 china-clone) work perfectly
with the 77 settings.

and in both case i never have the "blue screen" only black screen on zoneminder
and also was not able to have a videocapture work (test the kdetv)

i download the last vanilla kernel 2.6.24.2 and try to use it.

the problem continue to damn me...

here is the dmesg when i try to mount on the mod.

-------->modprobe bttv
bttv: driver version 0.9.17 loaded
bttv: using 8 buffers with 2080k (520 pages) each for capture
bttv: Bt8xx card found (0).
bttv0: Bt878 (rev 17) at 0000:04:08.0, irq: 5, latency: 64, mmio: 0xefc00000
bttv0: using: GrandTec Multi Capture Card (Bt878) [card=77,insmod option]
bttv0: gpio: en=00000000, out=00000000 in=00ffffff [init]
i2c-adapter i2c-0: adapter [bt878 #0 [sw]] registered
i2c-adapter i2c-0: found normal entry for adapter 0, addr 0x50
i2c-adapter i2c-0: master_xfer[0] W, addr=0x50, len=0
i2c-adapter i2c-0: i2c_outb: 0xa0, timeout at bit #7
i2c-adapter i2c-0: i2c_outb: 0xa0, timeout at bit #7
i2c-adapter i2c-0: i2c_outb: 0xa0, timeout at bit #7
i2c-adapter i2c-0: i2c_outb: 0xa0, timeout at bit #7
i2c-adapter i2c-0: Used 4 tries to write to client at 0x50: failed, timeout?
i2c-adapter i2c-0: NAK from device addr 0x50 msg #0
bttv0: tuner absent
bttv0: registered device video0
bttv0: registered device vbi0
bttv0: PLL: 28636363 => 35468950 . ok
bttv: Bt8xx card found (1).
bttv1: Bt878 (rev 17) at 0000:04:09.0, irq: 11, latency: 64, mmio: 0xefa00000
bttv1: using: GrandTec Multi Capture Card (Bt878) [card=77,insmod option]
bttv1: gpio: en=00000000, out=00000000 in=00ffffff [init]
i2c-adapter i2c-1: adapter [bt878 #1 [sw]] registered
i2c-adapter i2c-1: found normal entry for adapter 1, addr 0x50
i2c-adapter i2c-1: master_xfer[0] W, addr=0x50, len=0
i2c-adapter i2c-1: i2c_outb: 0xa0, timeout at bit #7
i2c-adapter i2c-1: i2c_outb: 0xa0, timeout at bit #7
i2c-adapter i2c-1: i2c_outb: 0xa0, timeout at bit #7
i2c-adapter i2c-1: i2c_outb: 0xa0, timeout at bit #7
i2c-adapter i2c-1: Used 4 tries to write to client at 0x50: failed, timeout?
i2c-adapter i2c-1: NAK from device addr 0x50 msg #0
bttv1: tuner absent
bttv1: registered device video1
bttv1: registered device vbi1
bttv1: PLL: 28636363 => 35468950 . ok
bttv: Bt8xx card found (2).
bttv2: Bt878 (rev 17) at 0000:04:0a.0, irq: 10, latency: 64, mmio: 0xef800000
bttv2: using: GrandTec Multi Capture Card (Bt878) [card=77,insmod option]
bttv2: gpio: en=00000000, out=00000000 in=00ffffff [init]
i2c-adapter i2c-2: adapter [bt878 #2 [sw]] registered
i2c-adapter i2c-2: found normal entry for adapter 2, addr 0x50
i2c-adapter i2c-2: master_xfer[0] W, addr=0x50, len=0
i2c-adapter i2c-2: i2c_outb: 0xa0, timeout at bit #7
i2c-adapter i2c-2: i2c_outb: 0xa0, timeout at bit #7
i2c-adapter i2c-2: i2c_outb: 0xa0, timeout at bit #7
i2c-adapter i2c-2: i2c_outb: 0xa0, timeout at bit #7
i2c-adapter i2c-2: Used 4 tries to write to client at 0x50: failed, timeout?
i2c-adapter i2c-2: NAK from device addr 0x50 msg #0
bttv2: tuner absent
bttv2: registered device video2
bttv2: registered device vbi2
bttv2: PLL: 28636363 => 35468950 . ok
bttv: Bt8xx card found (3).
bttv3: Bt878 (rev 17) at 0000:04:0b.0, irq: 3, latency: 64, mmio: 0xef600000
bttv3: using: GrandTec Multi Capture Card (Bt878) [card=77,insmod option]
bttv3: gpio: en=00000000, out=00000000 in=00ffffff [init]
i2c-adapter i2c-3: adapter [bt878 #3 [sw]] registered
i2c-adapter i2c-3: found normal entry for adapter 3, addr 0x50
i2c-adapter i2c-3: master_xfer[0] W, addr=0x50, len=0
i2c-adapter i2c-3: i2c_outb: 0xa0, timeout at bit #7
i2c-adapter i2c-3: i2c_outb: 0xa0, timeout at bit #7
i2c-adapter i2c-3: i2c_outb: 0xa0, timeout at bit #7
i2c-adapter i2c-3: i2c_outb: 0xa0, timeout at bit #7
i2c-adapter i2c-3: Used 4 tries to write to client at 0x50: failed, timeout?
i2c-adapter i2c-3: NAK from device addr 0x50 msg #0
bttv3: tuner absent
bttv3: registered device video3
bttv3: registered device vbi3
bttv3: PLL: 28636363 => 35468950 . ok
bttv: Bt8xx card found (4).
bttv4: Bt878 (rev 17) at 0000:04:0c.0, irq: 5, latency: 64, mmio: 0xef400000
bttv4: using: GrandTec Multi Capture Card (Bt878) [card=77,insmod option]
bttv4: gpio: en=00000000, out=00000000 in=00ffffff [init]
i2c-adapter i2c-4: adapter [bt878 #4 [sw]] registered
i2c-adapter i2c-4: found normal entry for adapter 4, addr 0x50
i2c-adapter i2c-4: master_xfer[0] W, addr=0x50, len=0
i2c-adai2c-adapter i2c-4: i2c_outb: 0xa0, timeout at bit #7
i2c-adapter i2c-4: i2c_outb: 0xa0, timeout at bit #7
i2c-adapter i2c-4: i2c_outb: 0xa0, timeout at bit #7
i2c-adapter i2c-4: Used 4 tries to write to client at 0x50: failed, timeout?
i2c-adapter i2c-4: NAK from device addr 0x50 msg #0
bttv4: tuner absent
bttv4: registered device video4
bttv4: registered device vbi4
bttv4: PLL: 28636363 => 35468950 . okpter i2c-4: i2c_outb: 0xa0, timeout at bit #7

bttv: Bt8xx card found (5).
bttv5: Bt878 (rev 17) at 0000:04:0d.0, irq: 11, latency: 64, mmio: 0xef200000
bttv5: using: GrandTec Multi Capture Card (Bt878) [card=77,insmod option]
bttv5: gpio: en=00000000, out=00000000 in=00ffffff [init]
i2c-adapter i2c-5: adapter [bt878 #5 [sw]] registered
i2c-adapter i2c-5: found normal entry for adapter 5, addr 0x50
i2c-adapter i2c-5: master_xfer[0] W, addr=0x50, len=0
i2c-adapter i2c-5: i2c_outb: 0xa0, timeout at bit #7
i2c-adapter i2c-5: i2c_outb: 0xa0, timeout at bit #7
i2c-adapter i2c-5: i2c_outb: 0xa0, timeout at bit #7
i2c-adapter i2c-5: i2c_outb: 0xa0, timeout at bit #7
i2c-adapter i2c-5: Used 4 tries to write to client at 0x50: failed, timeout?
i2c-adapter i2c-5: NAK from device addr 0x50 msg #0
bttv5: tuner absent
bttv5: registered device video5
bttv5: registered device vbi5
bttv5: PLL: 28636363 => 35468950 . ok
bttv: Bt8xx card found (6).
bttv6: Bt878 (rev 17) at 0000:04:0e.0, irq: 10, latency: 64, mmio: 0xef000000
bttv6: using: GrandTec Multi Capture Card (Bt878) [card=77,insmod option]
bttv6: gpio: en=00000000, out=00000000 in=00ffffff [init]
i2c-adapter i2c-6: adapter [bt878 #6 [sw]] registered
i2c-adapter i2c-6: found normal entry for adapter 6, addr 0x50
i2c-adapter i2c-6: master_xfer[0] W, addr=0x50, len=0
i2c-adapter i2c-6: i2c_outb: 0xa0, timeout at bit #7
i2c-adapter i2c-6: i2c_outb: 0xa0, timeout at bit #7
i2c-adapter i2c-6: i2c_outb: 0xa0, timeout at bit #7
i2c-adapter i2c-6: i2c_outb: 0xa0, timeout at bit #7
i2c-adapter i2c-6: Used 4 tries to write to client at 0x50: failed, timeout?
i2c-adapter i2c-6: NAK from device addr 0x50 msg #0
bttv6: tuner absent
bttv6: registered device video6
bttv6: registered device vbi6
bttv6: PLL: 28636363 => 35468950 . ok
bttv: Bt8xx card found (7).
bttv7: Bt878 (rev 17) at 0000:04:0f.0, irq: 3, latency: 64, mmio: 0xeee00000
bttv7: using: GrandTec Multi Capture Card (Bt878) [card=77,insmod option]
bttv7: gpio: en=00000000, out=00000000 in=00fffff2 [init]
i2c-adapter i2c-7: adapter [bt878 #7 [sw]] registered
i2c-adapter i2c-7: found normal entry for adapter 7, addr 0x50
i2c-adapter i2c-7: master_xfer[0] W, addr=0x50, len=0
i2c-adapter i2c-7: i2c_outb: 0xa0, timeout at bit #7
i2c-adapter i2c-7: i2c_outb: 0xa0, timeout at bit #7
i2c-adapter i2c-7: i2c_outb: 0xa0, timeout at bit #7
i2c-adapter i2c-7: i2c_outb: 0xa0, timeout at bit #7
i2c-adapter i2c-7: Used 4 tries to write to client at 0x50: failed, timeout?
i2c-adapter i2c-7: NAK from device addr 0x50 msg #0
bttv7: tuner absent
bttv7: registered device video7
bttv7: registered device vbi7
bttv7: PLL: 28636363 => 35468950 . ok

-----------------------------
appear that i've some trouble with the i2c-adapter (at least from what i can understand)
i suffer from a timeout at bit 7 ... what the F#@K is?

ok, the hardware i use is a asus pundit r-350
maybe is a irq issue? (i see that this card use 4 irq and are shared by other device too)

any suggestions is very welcome cause is a real hard fight here

.

thanks a lot.

Post by **cordel** » Sat Feb 16, 2008 5:02 pm

Well let us see your interrrupts

cat /proc/interrupts

sugacapra · Post by **sugacapra** » Mon Feb 18, 2008 9:10 am

root@videoserver:~# cat /proc/interrupts
CPU0
0: 905981 XT-PIC-XT timer
1: 10 XT-PIC-XT i8042
2: 0 XT-PIC-XT cascade
3: 231 XT-PIC-XT bttv3, bttv7
5: 286 XT-PIC-XT ATI IXP, bttv0, bttv4
8: 1 XT-PIC-XT rtc
9: 1 XT-PIC-XT acpi
10: 249 XT-PIC-XT ehci_hcd:usb1, ohci_hcd:usb2, ohci_hcd:usb3, bttv2, bttv6
11: 824 XT-PIC-XT bttv1, bttv5, eth0
14: 81103 XT-PIC-XT ide0
NMI: 0 Non-maskable interrupts
TRM: 0 Thermal event interrupts
SPU: 0 Spurious interrupts
ERR: 0

using sensors-detect:

i dont put the outcome, cut it and just the summary, but this stay
so looong trying to communicate with capt. card.

[...]

Next adapter: SMBus PIIX4 adapter at 0a00 (i2c-0)
Do you want to scan it? (YES/no/selectively):
Client found at address 0x52
Probing for `Analog Devices ADM1033'... No
Probing for `Analog Devices ADM1034'... No
Probing for `SPD EEPROM'... Success!
(confidence 8, driver `eeprom')

Next adapter: bt878 #0 [sw] (i2c-1)
Do you want to scan it? (YES/no/selectively):

Next adapter: bt878 #1 [sw] (i2c-2)
Do you want to scan it? (YES/no/selectively):

Next adapter: bt878 #2 [sw] (i2c-3)
Do you want to scan it? (YES/no/selectively):

Next adapter: bt878 #3 [sw] (i2c-4)
Do you want to scan it? (YES/no/selectively):

Next adapter: bt878 #4 [sw] (i2c-5)
Do you want to scan it? (YES/no/selectively):

Next adapter: bt878 #5 [sw] (i2c-6)
Do you want to scan it? (YES/no/selectively):

Next adapter: bt878 #6 [sw] (i2c-7)
Do you want to scan it? (YES/no/selectively):

Next adapter: bt878 #7 [sw] (i2c-8)
Do you want to scan it? (YES/no/selectively):
[...]

Now follows a summary of the probes I have just done.
Just press ENTER to continue:

Driver `eeprom' (should be inserted):
Detects correctly:
* Bus `SMBus PIIX4 adapter at 0a00'
Busdriver `i2c-piix4', I2C address 0x52
Chip `SPD EEPROM' (confidence:

EEPROMs are *NOT* sensors! They are data storage chips commonly
found on memory modules (SPD), in monitors (EDID), or in some
laptops, for example.

Driver `it87' (should be inserted):
Detects correctly:
* ISA bus, address 0x260
Chip `ITE IT8712F Super IO Sensors' (confidence: 9)

using lspci -vv -nn

00:00.0 Host bridge [0600]: ATI Technologies Inc Radeon 9100 IGP Host Bridge [1002:7833]
Subsystem: ASUSTeK Computer Inc. Unknown device [1043:8107]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Region 0: Memory at f0000000 (32-bit, prefetchable)
Region 1: Memory at feb00000 (32-bit, non-prefetchable)
Capabilities: [a0] AGP version 3.0
Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW+ AGP3+ Rate=x4,x8
Command: RQ=1 ArqSz=0 Cal=0 SBA+ AGP- GART64- 64bit- FW- Rate=<none>

00:01.0 PCI bridge [0604]: ATI Technologies Inc Radeon 9100 IGP PCI/AGP Bridge [1002:7838] (prog-if 00 [Normal de
code])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: fdb00000-fdefffff
Prefetchable memory behind bridge: dde00000-eddfffff
Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-

00:13.0 USB Controller [0c03]: ATI Technologies Inc OHCI USB Controller #1 [1002:4347] (rev 01) (prog-if 10 [OHCI
])
Subsystem: ASUSTeK Computer Inc. Unknown device [1043:8108]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size: 128 bytes
Interrupt: pin A routed to IRQ 10
Region 0: Memory at fe800000 (32-bit, non-prefetchable)

00:13.1 USB Controller [0c03]: ATI Technologies Inc OHCI USB Controller #2 [1002:4348] (rev 01) (prog-if 10 [OHCI
])
Subsystem: ASUSTeK Computer Inc. Unknown device [1043:8108]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size: 128 bytes
Interrupt: pin A routed to IRQ 10
Region 0: Memory at fe900000 (32-bit, non-prefetchable)

00:13.2 USB Controller [0c03]: ATI Technologies Inc EHCI USB Controller [1002:4345] (rev 01) (prog-if 20 [EHCI])
Subsystem: ASUSTeK Computer Inc. Unknown device [1043:8108]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size: 128 bytes
Interrupt: pin A routed to IRQ 10
Region 0: Memory at fea00000 (32-bit, non-prefetchable)
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Bridge: PM- B3+

00:14.0 SMBus [0c05]: ATI Technologies Inc SMBus [1002:4353] (rev 18)
Subsystem: ASUSTeK Computer Inc. Unknown device [1043:8108]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Region 0: I/O ports at 0a00
Region 1: Memory at 40000000 (32-bit, non-prefetchable)

00:14.1 IDE interface [0101]: ATI Technologies Inc Dual Channel Bus Master PCI IDE Controller [1002:4349] (prog-i
f 8a [Master SecP PriP])
Subsystem: ASUSTeK Computer Inc. Unknown device [1043:8108]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort+ <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at 01f0
Region 1: I/O ports at 03f4
Region 2: I/O ports at 0170
Region 3: I/O ports at 0374 [size=1]
Region 4: I/O ports at ff00 [size=16]

00:14.3 ISA bridge [0601]: ATI Technologies Inc Unknown device [1002:434c]
Subsystem: ASUSTeK Computer Inc. Unknown device [1043:8108]
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0

00:14.4 PCI bridge [0604]: ATI Technologies Inc Unknown device [1002:4342] (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Bus: primary=00, secondary=02, subordinate=03, sec-latency=64
Memory behind bridge: fdf00000-fe0fffff
Prefetchable memory behind bridge: ede00000-efdfffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-

00:14.5 Multimedia audio controller [0401]: ATI Technologies Inc IXP150 AC'97 Audio Controller [1002:4341]
Subsystem: ASUSTeK Computer Inc. Unknown device [1043:810d]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (500ns min), Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 5
Region 0: Memory at fe700000 (32-bit, non-prefetchable) [size=256]

01:05.0 VGA compatible controller [0300]: ATI Technologies Inc Radeon 9100 PRO IGP [1002:7834] (prog-if 00 [VGA])
Subsystem: ASUSTeK Computer Inc. Unknown device [1043:8107]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop+ ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (2000ns min), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 11
Region 0: Memory at e0000000 (32-bit, prefetchable) [size=128M]
Region 1: I/O ports at d000 [size=256]
Region 2: Memory at fde00000 (32-bit, non-prefetchable) [size=64K]
Expansion ROM at fdd00000 [disabled] [size=128K]
Capabilities: [58] AGP version 3.0
Status: RQ=256 Iso- ArqSz=0 Cal=7 SBA+ ITACoh- GART64- HTrans- 64bit+ FW+ AGP3+ Rate=x4,x8
Command: RQ=1 ArqSz=0 Cal=0 SBA+ AGP- GART64- 64bit- FW- Rate=<none>
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

02:09.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ [10ec:8139] (rev 10)
Subsystem: Realtek Semiconductor Co., Ltd. RT8139 [10ec:8139]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (8000ns min, 16000ns max)
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at e800 [size=256]
Region 1: Memory at fe000000 (32-bit, non-prefetchable) [size=256]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0-,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

02:0e.0 PCI bridge [0604]: Hint Corp HiNT HB4 PCI-PCI Bridge (PCI6150) [3388:0022] (rev 04) (prog-if 00 [Normal d
ecode])
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size: 64 bytes
Bus: primary=02, secondary=03, subordinate=03, sec-latency=64
Prefetchable memory behind bridge: 00000000ede00000-00000000efdfffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [e4] #06 [0094]
Capabilities: [e8] Vital Product Data

03:08.0 Multimedia video controller [0400]: Brooktree Corporation Bt878 Video Capture [109e:036e] (rev 11)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (4000ns min, 10000ns max)
Interrupt: pin A routed to IRQ 5
Region 0: Memory at efc00000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

03:08.1 Multimedia controller [0480]: Brooktree Corporation Bt878 Audio Capture [109e:0878] (rev 11)
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 5
Region 0: Memory at efd00000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

03:09.0 Multimedia video controller [0400]: Brooktree Corporation Bt878 Video Capture [109e:036e] (rev 11)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (4000ns min, 10000ns max)
Interrupt: pin A routed to IRQ 11
Region 0: Memory at efa00000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

03:09.1 Multimedia controller [0480]: Brooktree Corporation Bt878 Audio Capture [109e:0878] (rev 11)
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 11
Region 0: Memory at efb00000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

03:0a.0 Multimedia video controller [0400]: Brooktree Corporation Bt878 Video Capture [109e:036e] (rev 11)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (4000ns min, 10000ns max)
Interrupt: pin A routed to IRQ 10
Region 0: Memory at ef800000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

03:0a.1 Multimedia controller [0480]: Brooktree Corporation Bt878 Audio Capture [109e:0878] (rev 11)
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 10
Region 0: Memory at ef900000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

03:0b.0 Multimedia video controller [0400]: Brooktree Corporation Bt878 Video Capture [109e:036e] (rev 11)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (4000ns min, 10000ns max)
Interrupt: pin A routed to IRQ 3
Region 0: Memory at ef600000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

03:0b.1 Multimedia controller [0480]: Brooktree Corporation Bt878 Audio Capture [109e:0878] (rev 11)
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 3
Region 0: Memory at ef700000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

03:0c.0 Multimedia video controller [0400]: Brooktree Corporation Bt878 Video Capture [109e:036e] (rev 11)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (4000ns min, 10000ns max)
Interrupt: pin A routed to IRQ 5
Region 0: Memory at ef400000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

03:0c.1 Multimedia controller [0480]: Brooktree Corporation Bt878 Audio Capture [109e:0878] (rev 11)
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 5
Region 0: Memory at ef500000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
03:0d.0 Multimedia video controller [0400]: Brooktree Corporation Bt878 Video Capture [109e:036e] (rev 11)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (4000ns min, 10000ns max)
Interrupt: pin A routed to IRQ 11
Region 0: Memory at ef200000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

03:0d.1 Multimedia controller [0480]: Brooktree Corporation Bt878 Audio Capture [109e:0878] (rev 11)
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 11
Region 0: Memory at ef300000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

03:0e.0 Multimedia video controller [0400]: Brooktree Corporation Bt878 Video Capture [109e:036e] (rev 11)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (4000ns min, 10000ns max)
Interrupt: pin A routed to IRQ 10
Region 0: Memory at ef000000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

03:0e.1 Multimedia controller [0480]: Brooktree Corporation Bt878 Audio Capture [109e:0878] (rev 11)
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 10
Region 0: Memory at ef100000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

03:0f.0 Multimedia video controller [0400]: Brooktree Corporation Bt878 Video Capture [109e:036e] (rev 11)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (4000ns min, 10000ns max)
Interrupt: pin A routed to IRQ 3
Region 0: Memory at eee00000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

03:0f.1 Multimedia controller [0480]: Brooktree Corporation Bt878 Audio Capture [109e:0878] (rev 11)
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 3
Region 0: Memory at eef00000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

root@videoserver:/var/log/zm# tail -n20 zmdc.log
02/18/08 10:03:53.081789 zmdc[4012].INF ['zmc -d /dev/v4l/video3' starting at 08/02/18 10:03:53, pid = 4245]
02/18/08 10:03:53.657825 zmdc[4012].ERR ['zmc -d /dev/v4l/video3' exited abnormally, exit status 255]
02/18/08 10:03:55.056221 zmdc[4012].INF [Starting pending process, zmc -d /dev/v4l/video1]
02/18/08 10:03:55.093832 zmdc[4012].INF ['zmc -d /dev/v4l/video1' starting at 08/02/18 10:03:55, pid = 4246]
02/18/08 10:03:55.633624 zmdc[4012].ERR ['zmc -d /dev/v4l/video1' exited abnormally, exit status 255]
02/18/08 10:03:56.032177 zmdc[4012].INF [Starting pending process, zmc -d /dev/v4l/video0]
02/18/08 10:03:56.049730 zmdc[4012].INF ['zmc -d /dev/v4l/video0' starting at 08/02/18 10:03:56, pid = 4247]
02/18/08 10:03:56.050265 zmdc[4012].INF [Starting pending process, zmc -d /dev/v4l/video2]
02/18/08 10:03:56.112455 zmdc[4012].INF ['zmc -d /dev/v4l/video2' starting at 08/02/18 10:03:56, pid = 4248]
02/18/08 10:03:56.681663 zmdc[4012].ERR ['zmc -d /dev/v4l/video0' exited abnormally, exit status 255]
02/18/08 10:03:56.777794 zmdc[4012].ERR ['zmc -d /dev/v4l/video2' exited abnormally, exit status 255]
02/18/08 10:03:58.076204 zmdc[4012].INF [Starting pending process, zmc -d /dev/v4l/video5]
02/18/08 10:03:58.113793 zmdc[4012].INF ['zmc -d /dev/v4l/video5' starting at 08/02/18 10:03:58, pid = 4249]
02/18/08 10:03:58.701812 zmdc[4012].ERR ['zmc -d /dev/v4l/video5' exited abnormally, exit status 255]
02/18/08 10:03:59.000175 zmdc[4012].INF [Starting pending process, zmc -d /dev/v4l/video6]
02/18/08 10:03:59.037817 zmdc[4012].INF ['zmc -d /dev/v4l/video6' starting at 08/02/18 10:03:59, pid = 4250]
02/18/08 10:03:59.625808 zmdc[4012].ERR ['zmc -d /dev/v4l/video6' exited abnormally, exit status 255]
02/18/08 10:04:00.024219 zmdc[4012].INF [Starting pending process, zmc -d /dev/v4l/video7]
02/18/08 10:04:00.061744 zmdc[4012].INF ['zmc -d /dev/v4l/video7' starting at 08/02/18 10:04:00, pid = 4251]
02/18/08 10:04:00.649805 zmdc[4012].ERR ['zmc -d /dev/v4l/video7' exited abnormally, exit status 255]

this help in some manners?