TP-Link NC450

Post here to ask any questions about hardware suitability, configuration in ZoneMinder, or experiences. If you just want to know if something works with ZoneMinder or not, please check the Hardware Compatibility sections in the forum, and the Wiki first. Also search this topic as well.
Post Reply
maqic
Posts: 2
Joined: Fri Jan 20, 2017 7:21 am

TP-Link NC450

Post by maqic » Fri Jan 20, 2017 7:28 am

Greetings Everyone,

I am just wondering is anyone able to add TP-link NC450 to their ZoneMinder 1.3.0 setup?

I recently able to install my first Zoneminder 1.3.0 on my Ubuntu 16.10 system and it seems working fine except I am not able to add or view my TP-link NC450 v2.0 firmware 1.1.2 Build 161013 .

Thanks,

Matt G.

maqic
Posts: 2
Joined: Fri Jan 20, 2017 7:21 am

Re: TP-Link NC450

Post by maqic » Fri Jan 20, 2017 8:07 am

Hello Again to Everyone,

I am able to find the way to add TP-Link NC450 v2.0 to my Zoneminder v 1.3.0 setup and willing to share it with all who is in need of some help.

I believe this is the first time this that someone is sharing this IP camera settings so that It will help someone other than me.

GENERAL


Source Type: cURL (HTTP(S) only)

SOURCE

URL: http://<ip_address>:8080/stream/video/mjpeg
Username: admin
Password: !! Your passwords base64 encoded version !!
Capture Width: 1280
Capture Height: 720

You need to change the <ip_address> section with the local IP address of your Camera (ex: 192.168.1.11 or 10.0.0.11)
You can also change your password to base64 format via this website https://www.base64encode.org/ .

if you need any further details please let me know.

Thanks,

Matt G.

cyclonmaster
Posts: 1
Joined: Thu Jan 26, 2017 8:48 am

Re: TP-Link NC450

Post by cyclonmaster » Thu Jan 26, 2017 8:55 am

Thank you for sharing mpeg video stream url for TP-Link NC450.

This type of IP Camera has support for PTZ Control.
Anyone know what is the stream url for the PTZ Control?
I want to stream the camera and control the PTZ through web.

Please advice.

bernd.wechner
Posts: 5
Joined: Mon Aug 08, 2016 5:49 am

Re: TP-Link NC450

Post by bernd.wechner » Tue Feb 14, 2017 8:36 pm

Thank you kindly maqic, for confirming you have this camera working with zoneminder. I was pleased to find this and 'm watching this thread to see if anyone has a PTZ solution and will post one should I happen upon one myself.

bernd.wechner
Posts: 5
Joined: Mon Aug 08, 2016 5:49 am

Re: TP-Link NC450

Post by bernd.wechner » Wed Feb 15, 2017 5:58 am

I have, by sniffing the web interface and testing, established that directional control is possible via:

Code: Select all

http://cameraip/setTurnDirection.fcgi?operation=start&dir=X
where X is one of: n,s, e, w, ne, nw, se, sw

if you stick that into your browser it turns the camera.

Not sure if that can be exploited in Zoneminder as I haven't installed it yet. Came here checking to see if the NC450 would work with Zoneminder before bothering to. It seems basic streaming is possible.

etsi
Posts: 3
Joined: Thu Feb 16, 2017 10:51 am

Re: TP-Link NC450

Post by etsi » Thu Feb 16, 2017 10:53 am

Hello,

Motion detection works using NC450 and zoneminder? Because the firmware doesn't support any detection.

Thanks

bernd.wechner
Posts: 5
Joined: Mon Aug 08, 2016 5:49 am

Re: TP-Link NC450

Post by bernd.wechner » Fri Feb 17, 2017 5:33 am

The NC450 does support motion detection in its firmware, but only the saving of JPG snapshots in response. I am wondering if and will in time explore whether, Zoneminder has motion detection and can save video segments rather than snapshots in response to detected motion. That is my goal.
etsi wrote:Motion detection works using NC450 and zoneminder? Because the firmware doesn't support any detection.
I admit though, that I am not sure what you mean by this? Can you clarify?

etsi
Posts: 3
Joined: Thu Feb 16, 2017 10:51 am

Re: TP-Link NC450

Post by etsi » Fri Feb 17, 2017 5:56 am

bernd.wechner wrote:
etsi wrote:Motion detection works using NC450 and zoneminder? Because the firmware doesn't support any detection.
I admit though, that I am not sure what you mean by this? Can you clarify?
I mean if the NC450 works with zoneminder and motion detection. I find the camera very cheap and I wonder if it's worth buy it.

bernd.wechner
Posts: 5
Joined: Mon Aug 08, 2016 5:49 am

Re: TP-Link NC450

Post by bernd.wechner » Fri Feb 17, 2017 6:12 am

Well, I can't say yet. I don't know Zoneminder well enough. It looks a real chore to install and I was here to confirm it was worth my while as I am planning to use the NC450. I have some other streaming cameras and if Zoneminder is good may look at those too but my main interest for now is the NC450.

jaddie
Posts: 1
Joined: Mon Mar 13, 2017 10:53 am

Re: TP-Link NC450

Post by jaddie » Mon Mar 13, 2017 10:56 am

I was just reading through this and wondered if anyone had got anywhere with getting audio in Zoneminder, as I have it setup with ffmpeg at the moment but don't seem to be able to hear anything

rtsp://username:password@camera-address/h264_vga.sdp -- This works with ffmpeg RTP/RTSP which I have set to 32bit colour and 1280x720

But yeah, I was just wondering before I spend hours trying to work around this, if anyone had audio working & also the PTZ for the camera?

Post Reply

Who is online

Users browsing this forum: No registered users and 1 guest