ZoneMinder Forums

I'm adding an scp option to the Options->FTP configuration tab. I got the correct data in the Config table and my option now shows up in the GUI. I was expecting to see an auto increment attribute on the ID column. using a 0 as the ID caused zm not to start. No worries I did a select max on id and j...

Is this the appropriate forum for asking ZM development questions?

Well that's what I thought as well. Version 1.24.1 preset for the ACTi had a remote host sub path set to '/track'. The remote host sub path went away for this preset in the 1.24.2 version. I had concerns about this and posted questions for clarification. From the forum replies it sounds like it's no...

Yes sir. I did use ACTi presets. Camera: ACTi 3511 Protocol: RTSP Remote Method: RTP/Unicast Remote Port: 7070 Capture Width: 640 Capture Height: 480 Remote Image colors: 24 bit color Here's the zmu output: root@emu:/var/log# zmu -m 1 -q Id : 1 Name : CompRmWest Type : Remote Protocol : rtsp Host : ...

I can't get zoneminder working on my fresh Ubuntu 64bit install with ACTi IP cameras. I've followed the build and install guides on the wiki several times with the same results. Zoneminder and ffmpeg where built from the svn repositories. I even went back to the ffmpeg 0.5 and zoneminder 1.24.1 base...

OK. Great. Thank you for the clarification.

I received a pop up on my browser telling me to upgrade to a newer version of mootools (1.2.1).
Mootools version 1.11 is installed in ZM. Is the ZM update service suppose to update
mootools or is it a manual process?

I looked over the forum post you suggested however it didn't yield any clues. Not having access to the ACTi API make it difficult to figure out whats needed for the remote RTSP settings. I used the one and only ACTi preset in 1.24.1 which worked without a hitch. cordel suggested that I use the prese...

I just did a fresh install of 1.24.2 on Ubuntu Hardy 64bit After adding a new zone my ACTi IP camera's are not working. I noticed that there is no longer a 'Remote Host SubPath' on the Source tab. Was this by design or did it slip through the cracks? My 1.24.1 install filled in the value '/track' wh...

Yes that was helpful. Thank you monex for your post.

I have accumulated a huge number of events and need to delete them. Using the gui would take me hours. I can always go into the www events directory and delete them however I'm pretty sure there are corresponding entries in the data base. Are there any zm scripts/tools which I can use from the comma...

Is there anyway to configure zm to record for a minimum amount of time for each event? I'd like to bracket the recording to say 15 seconds prior to alarm and 15 seconds post alarm. I believe this is controlled by the pre/post event image count . according to the docs the pre event count should not e...

I think you already have this but heres the system info on my ACTi ACM-3511 Firmware Version = A1D-220-V3.09.14-AC MAC Address = 00:0F:7C:02:3C:CF Production ID = ACM3511-08L-X-00005 Factory Default Type = Two Ways Audio (0x71) Company Name = ACTi Corporation WEB Site = www.acti.com Profile ID = MT9...

I tried deleting the zone and recreating once again as suggested in a previous 1.23 post.
This time it worked. My zone triggers an alarm and then ends. Unfortunately now my alarms end prematurely They range from 3-4 seconds and end even though there is activity.

I have a fresh install of ZM 1.24.1 and ffmpeg. My events trigger ok however they never end. I have to click the 'Disable alarms' link to end the event. Does this sound like a zm configuration issue or possibly my camera settings need to be tuned? Monitor Zone setup for 'modect' Kernel: Linux emu 2....