I've 3 REMOTE cams. 2 AXIS 210 and 1 Panasonic.
The server is a PRoliant DL120 G5 (Dual core Xeon 2GHz), 250GB + 500GB HDDs, Gigabit Ethernet, 1GB RAM with Ubuntu 8.10
I use modect to save events, but this events are saved at maxium of 6FPS... sometimes at less than 1FPS. CPU does not reachs more than 15%
Memory is:
Mem: 1011080k total, 986608k used, 24472k free, 77660k buffers
Swap: 2961400k total, 124944k used, 2836456k free, 545344k cached
I think that it would be a memory problem.
Can Yo confirm it with this values?
If I upgrade t 4GB, Will the FPS increas automatically?
Thanks
Question about FPS and performance
Re: Question about FPS and performance
[quote="maikdema"]I've 3 REMOTE cams. 2 AXIS 210 and 1 Panasonic.
The server is a PRoliant DL120 G5 (Dual core Xeon 2GHz), 250GB + 500GB HDDs, Gigabit Ethernet, 1GB RAM with Ubuntu 8.10
I use modect to save events, but this events are saved at maxium of 6FPS... sometimes at less than 1FPS. CPU does not reachs more than 15%
I think that it would be a memory problem.
Can Yo confirm it with this values?
If I upgrade t 4GB, Will the FPS increas automatically?
Thanks[/code]
The server is a PRoliant DL120 G5 (Dual core Xeon 2GHz), 250GB + 500GB HDDs, Gigabit Ethernet, 1GB RAM with Ubuntu 8.10
I use modect to save events, but this events are saved at maxium of 6FPS... sometimes at less than 1FPS. CPU does not reachs more than 15%
Code: Select all
Memory is:
total used free shared buffers cached
Mem: 1011080 986404 24676 0 77732 545376
-/+ buffers/cache: 363296 647784
Swap: 2961400 124944 2836456
Can Yo confirm it with this values?
If I upgrade t 4GB, Will the FPS increas automatically?
Thanks[/code]
I've been searching more about performnce.
I've seen that CPU usage shown on ZM main page is not asI thougth.
1.0 = 100% CPU
2.0 = 200% (or 100% of each CPU if you have 2 cores)
so, I've an average of this value of 1.5~2.0
I think it could be a overload prloblem.
Maybe MODECT to all 3 cams consumes more CPU than it can afford?
I know is a bad idea, but I've X system with gnome installed and runing, showing Montage on the server's room. Does this consume lot of resources?
I've seen that CPU usage shown on ZM main page is not asI thougth.
1.0 = 100% CPU
2.0 = 200% (or 100% of each CPU if you have 2 cores)
so, I've an average of this value of 1.5~2.0
I think it could be a overload prloblem.
Maybe MODECT to all 3 cams consumes more CPU than it can afford?
I know is a bad idea, but I've X system with gnome installed and runing, showing Montage on the server's room. Does this consume lot of resources?
by now you must have tried by... turning off browser and X all together.
if not, then indeed it will bog you down running x and montage view on your zm server.
you should look into other ways to view monitors if you need to have them up 24/7.
even if you view montage on another PC it will increase your load
if not, then indeed it will bog you down running x and montage view on your zm server.
you should look into other ways to view monitors if you need to have them up 24/7.
even if you view montage on another PC it will increase your load